安徽省象形字數控機床有限公司是數控折彎機、數控剪板機等產品專業生產加工的公司，擁有完整、科學的質

量管理體系。安徽省象形字數控機床有限公司的誠信、實力和產品質量獲得業界的認可。坐落在中國經濟發展的

前沿—馬鞍山 比鄰 六朝古都 南京，占地面積6000平方米，現有員工200人，其中各級專精尖人才20多名。

公司專業設計、生產、銷售電液伺服數控折彎機、數控液壓閘式、擺式剪板機及普通型液壓折彎機、液壓剪板機

等板金加工設備，目前象形字已成為數控折彎機、剪板機生產基地之一。

性能特點：

 本機器采用鋼板焊接結構,機身采用有限元分析設計、振動時效消除內應力，使機身穩定、可靠。

◎采用三點支撐滾動導輪，消除支撐間隙，提高剪切精度。

◎刀架剪切角能在一定的范圍內調整，可使剪切材料變形量減小到理想狀態，又可剪切超厚板料。

◎剪切行程任意調整，提高了工作效率，又可實現分段剪切功能。

◎后擋料設計了手動抬升功能，便于超長板料剪切。

◎墻板內側設有手動加油泵，操作方便，保證關鍵部位的潤滑。

◎插裝式液壓系統，減緩油溫提升，增強機床運行的可靠性和安全性。

◎標配采用Delem專用系統，剪切計數、后擋料、剪切角及刀口間隙的調節直觀、簡單、方便。

◎可選用DAC310、DAC360數控系統以滿足更高精度要求的剪切和控制。

Performance features:

This machine adopts the welded structure of the steel plate, and the fuselage is designed and vibration aging is eliminated and the

internal stress is eliminated, so the fuselage is stable and reliable..
Using the three point support rolling guide, eliminate the support gap, improve the cutting precision.
a shearing angle can be adjusted in a certain range, can reduce the shearing deformation, and shear super thick material.
The shearing stroke adjust, improve work efficiency, and can realize sectional shear function.
The rear stopper is designed for manual lifting function, long sheet metal shear.
The inner side of the wall with manual pumps, convenient operation, ensure the lubrication of the key parts.
The plug-in type hydraulic system, slow temperature increase, enhance the reliability and safety operation of machine.
a standard uses a special system of delem, counting shearing, the block material, shear angle and cutting edge gap

visual adjustment, simple and convenient.
You can choose DAC310, DAC360 CNC system to meet the control requirements of shear and high accuracy.

擺式剪板機維護保養的方法

1、嚴格按照操作規程進行操作。

2、每次開機前按潤滑圖表要求定時、定點、定量加潤滑油，油應清潔無沉淀。

3、機床必須經常保持清潔，未油漆的部分應涂抹防銹油脂。

4、電動機軸承內的潤滑漾油要定期更換加注，并經常檢查電器部分工作是否正常安全可靠。

5、定期檢查鏈條、手柄、旋鈕、按鍵是否損壞，磨損嚴重的應及時更換，并報備件補充。

6、定期檢查修理開關、保險、手柄、保證其工作可靠。

7、每天下班前10分鐘，對機床加油潤滑及擦洗清潔機床。

8、嚴禁非指定人員操作該設備，平常必須做到人離機停。

Shears maintenance method
1, strictly follow the operation procedures for operation.
2, every time before the start of the lubrication chart to require the timing, fixed point, quantitative lubricating oil, oil should be clean without precipitation.
3, machine tools must often keep clean, the part of the paint should be coated with rust preventive grease.
4, motor bearing lubrication overflow oil should be changed regularly filling, and always check whether the normal work of safe and reliable electrical parts.
5, regularly check the chain, handle, knob, key press whether damage, wear serious should be replaced, and to spare parts for spare.
6, check the repair switch, insurance, handle, guarantee its work reliably.
10, 7 minutes before work every day, lubrication and cleaning machine tool for machine tools.
8, non designated personnel to operate the device, usually must be done to stop the machine.